[2017 Latest Cisco Version] Cisco 100-105 Dumps Latest Exam Questions And Answers Update Youtube Demo

Latest Cisco ICND1 100-105 dumps pdf materials and dumps vce youtube update free demo. Lead4pass Cisco 100-105 dumps exam questions and answers are updated (332 Q&As) are verified by experts. “Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)” is the name of Cisco https://www.lead4pass.com/100-105.html exam dumps which covers all the knowledge points of the real Cisco exam. High quality Cisco ICND1 100-105 dumps pdf training resources and study guides free try, pass Cisco 100-105 exam test easily.

Latest Cisco 100-105 dumps pdf questions and answers free download: https://drive.google.com/open?id=0B_7qiYkH83VReEJYRlhNVjdGeVU

Latest Cisco 300-101 dumps pdf questions and answers free download: https://drive.google.com/open?id=0B_7qiYkH83VRWFlVNGtTZjU1MVE

Vendor: Cisco
Certifications: ICND1
Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)
Exam Code: 100-105
Total Questions: 332 Q&As
100-105 dumps
QUESTION 1
Some routers have been configured with default routes. What are some of the advantages of using default routes? (Choose two)
A. They establish routes that will never go down.
B. They keep routing tables small.
C. They require a great deal of CPU power.
D. They allow connectivity to remote networks that are not in the routing table
E. They direct traffic from the internet into corporate networks.
Correct Answer: BD

QUESTION 2
Why would a network administrator configure port security on a switch?
A. to prevent unauthorized Telnet access to a switch port
B. to prevent unauthorized hosts from accessing the LAN
C. to limit the number of Layer 2 broadcasts on a particular switch port
D. block unauthorized access to the switch management interfaces
Correct Answer: B

QUESTION 3
What is one requirement for interfaces to run IPv6?
A. An IPv6 address must be configured on the interface.
B. An IPv4 address must be configured.
C. Stateless autoconfiguration must be enabled after enabling IPv6 on the interface.
D. IPv6 must be enabled with the ipv6 enable command in global configuration mode.
Correct Answer: A

QUESTION 4
Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.)
100-105 dumps Router(config)# router ospf 1
A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.
Correct Answer: CD

QUESTION 5
Which option is the default switch port port-security violation mode?
A. shutdown
B. protect
C. shutdown vlan
D. restrict
Correct Answer: A

QUESTION 6
Which method does a connected trunk port use to tag VLAN traffic?
A. IEEE 802 1w
B. IEEE 802 1D
C. IEEE 802 1Q
D. IEEE 802 1p
Correct Answer: C

QUESTION 7
100-105 dumps
100-105 dumps
Which of the following is true regarding the configuration of SwitchA?
A. only 5 simultaneous remote connections are possible
B. remote connections using ssh will require a username and password
C. only connections from the local network will be possible
D. console access to SwitchA requires a password
Correct Answer: B

QUESTION 8
Which statements are TRUE regarding Internet Protocol version 6 (IPv6) addresses? (Choose three.)
A. An IPv6 address is divided into eight 16-bit groups.
B. A double colon (::) can only be used once in a single IPv6 address.
C. IPv6 addresses are 196 bits in length.
D. Leading zeros cannot be omitted in an IPv6 address.
E. Groups with a value of 0 can be represented with a single 0 in IPv6 address.
Correct Answer: ABE

QUESTION 9
Which two of these statements are true of IPv6 address representation? 100-105 dumps (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC

QUESTION 10
The command ip route 192.168.100.160 255.255.255.224 192.168.10.2 was issued on a router. No routing protocols or other static routes are configured on the router. Which statement is true about this command?
A. The interface with IP address 192.168.10.2 is on this router.
B. The command sets a gateway of last resort for the router.
C. Packets that are destined for host 192.168.100.160 will be sent to 192.168.10.2.
D. The command creates a static route for all IP traffic with the source address 192.168.100.160.
Correct Answer: C

QUESTION 11
Which destination IP address can a host use to send one message to multiple devices across different subnets?
A. 172.20.1.0
B. 127.0.0.1
C. 192.168.0.119
D. 239.255.0.1
Correct Answer: D

QUESTION 12
A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?
A. decrease the window size
B. use a different source port for the session
C. decrease the sequence number
D. obtain a new IP address from the DHCP server
E. start a new session using UDP
Correct Answer: A

Reference: https://www.lead4pass.com/100-105.html dumps exam questions and answers free update. The best Cisco ICND1 100-105 dumps exam training materials and study guides free try.

Watch the video to learn more: https://youtu.be/trVHfqmuVvg